Hydraulic Breaker Maintenance: Checks by Shift and Service
Hydraulic breaker maintenance in four routines: before each shift, during work, scheduled service and storage, with model figures to keep on a service card.
All buyer guides
Hydraulic breaker maintenance comes down to four routines: a walk-round before each shift, correct greasing and handling during work, a scheduled service for the gas charge and seals, and safe storage. Each routine protects different parts. This guide sets out the four, links every check to its detailed guide, and lists the model figures worth keeping with the machine.
Hydraulic breaker maintenance before each shift
Walk round the breaker with the attachment lowered and the engine off.
| Check | What to look for | Detailed guide |
|---|---|---|
| Hoses and fittings | Chafing, cracks, loose couplings, an oil film | Hose guide |
| Oil leakage | Fresh oil at the tool, the body joints or the ports | Oil leak causes |
| Tool and retainer pins | Cracks, a mushroomed or chipped tip, pins fully seated | Pin guide |
| Tool bushing | Visible play of the tool in the front head | Bushing wear guide |
| Through bolts | Movement or a gap at the body joints | Through bolts guide |
| Grease | Fresh grease at the tool, grease supply filled | Grease guide |
Anything found here is quicker to fix now than after a shift of blows. At the top rate a small breaker strikes up to 66,000 times an hour, so a loose bolt or a dry bushing does not stay small.
Hydraulic breaker maintenance during work
- Grease in the right position. Press the tool into its working position before greasing, as the model manual describes. The grease guide explains why the position matters.
- Stop when the material breaks. Blows with nothing under the tool, called blank firing, send the energy back into the breaker.
- Do not pry. The tool is made to take blows along its axis. Levering with it bends the tool and loads the bushings.
- Reposition instead of holding one spot. If the material does not break, move to an edge or a new point.
- Watch the oil temperature. Oil that runs hotter with the breaker than with the bucket points to the flow or relief setting. Check both against the model window.
Operating technique is covered step by step in how to use a hydraulic breaker.
Scheduled hydraulic breaker maintenance
The interval comes from the model manual and the duty of the job. The service itself covers the same items on every breaker.
- Nitrogen charge. Pressure in the back head, and in the accumulator where one is fitted, is checked by trained staff against the model chart. See the nitrogen pressure guide.
- Seals. Seals are inspected, and replacements come as a kit for the exact model. See the seal kit guide.
- Accumulator diaphragm. Checked with the gas system. See the accumulator and diaphragm guide.
- Bushings. Wear is measured against the limit in the model manual. See the bushing wear guide.
- Piston and valve. Surfaces are inspected whenever the breaker is opened. See the piston guide and the valve guide.
- Through bolts. Inspected and tensioned to the model values. See the through bolts guide.
Figures to keep on the service card
Good hydraulic breaker maintenance starts with knowing what the carrier should deliver. Four figures per model tell a mechanic whether the excavator is feeding the breaker correctly. A reading outside the window is the first thing to correct, before any part is changed.
| Model | Chisel diameter | Oil flow | Working pressure | Impact rate |
|---|---|---|---|---|
| LC-40 | 40 mm | 15–30 L/min | 90–120 bar | 600–1,100 BPM |
| LC-45 | 45 mm | 20–40 L/min | 90–120 bar | 600–1,100 BPM |
| LC-53 | 53 mm | 20–50 L/min | 90–130 bar | 600–1,100 BPM |
| LC-68 | 68 mm | 40–60 L/min | 90–130 bar | 500–990 BPM |
| LC-75 | 75 mm | 50–90 L/min | 120–150 bar | 450–980 BPM |
| LC-100 | 100 mm | 80–110 L/min | 150–180 bar | 350–700 BPM |
| LC-135 | 135 mm | 100–150 L/min | 160–180 bar | 350–500 BPM |
| LC-140 | 140 mm | 120–180 L/min | 160–220 bar | 350–450 BPM |
| LC-150 | 150 mm | 130–190 L/min | 170–190 bar | 280–400 BPM |
| LC-155 | 155 mm | 180–240 L/min | 180–230 bar | 200–300 BPM |
| LC-165 | 165 mm | 190–260 L/min | 200–240 bar | 150–300 BPM |
| LC-175 | 175 mm | 200–250 L/min | 210–240 bar | 120–200 BPM |
| LC-195 | 195 mm | 250–320 L/min | 260–300 bar | 100–140 BPM |
| LC-200 | 200 mm | 260–340 L/min | 260–300 bar | 100–140 BPM |
| LC-230 | 230 mm | 330–430 L/min | 260–300 bar | 90–130 BPM |
Figures from the LICH model specifications, read on 13 November 2026.
Storage
- Clean the breaker and cap the hose ends so dirt stays out of the oil ports.
- Grease the tool and the exposed part of the front head.
- Rest the breaker in the position the manual approves, on a stand rated for its weight. The breaker stand guide covers selection, and the weight chart gives the weight of each model.
- For long storage, follow the manual for the gas charge and the piston position.
Questions about hydraulic breaker maintenance
What hydraulic breaker maintenance is done every day?
The six checks in the first table: hoses, leaks, tool and pins, bushing play, through bolts and grease.
How often should a hydraulic breaker be greased?
Through the shift during heavy breaking. The exact interval and quantity come from the model manual, and fresh grease at the tool is the sign that it is reaching the bushings.
When should the nitrogen pressure be checked?
At each scheduled service, and whenever the blows weaken with correct oil flow and pressure.
Which spare parts support hydraulic breaker maintenance on site?
Start with a spare tool and a seal kit for the exact model. The hydraulic breaker parts page lists parts by model, and the first-order spare parts guide covers quantities.
Keep Comparing
Compare more breaker models and buyer guides related to this topic.
